Stainless steel floor drain for kitchens, industrial settings, and workshops. Designed for long-lasting durability and easy installation in environments with light loads and a need for efficient handling of large flows.

Floor drain FURO 113

Flexible floor drain designed for high flow rates. Ideal for environments such as kitchens, restaurants, and industries with light loads. Many stocked sizes available for quick delivery.

Stainless steel, slip-resistant grid grate in a divided design. The maximum weight per part is 6 kg to facilitate cleaning of the drains and avoid heavy lifting. Use the accessory Lifting Hook as an aid.
The drain's construction allows for easy care and maintenance.
Adapted for several common floor types and features 360° rotatable and angle-adjustable outlets.
A water trap with a handle is included as standard.
The drain's flexibility can be further extended with a wide range of optional extras.
Manufactured as standard in acid-resistant stainless steel, grade EN 1.4404. This is not always necessary in large kitchens but provides better resistance to corrosion from salt and strong chemicals used in cleaning. The drain can also be ordered in stainless steel EN 1.4301 (SS 2333).
EPDM rubber seals according to EN 681-1 type Wc.

Installation

Delivered pre-assembled and covered to prevent concrete from flowing into the drain during casting (up to a width of 400 mm).
For screed floors, recess strips are included on the bonding flanges.
Sturdy mounting lugs for various anchoring in the floor structure are included.
Adjustable feet for easy installation and height adjustment are offered. See the Installation Accessories section.

L15 For areas with light weight traffic. Tested acc. to EN 1253-1 with 10 kN load.

Type-approved TG No SC0409-18 and meets the requirements of the applicable standard for floor drains, SS-EN 12531:2015. The approval applies to installation in concrete floors for tiled floors, plastic flooring, or screed floors. Also applicable for wooden joists in combination with plastic flooring. Type-approved for fire rating EI 60 according to Kiwa Certificate TG 1267.

If the drain is to be placed near large cooking pots, a depth of 150 or 200 mm should be chosen to increase the accumulating volume in the pit. In that case, accessories like the 2.7 L strainer basket and the extension part are also suitable choices.

Variants

Variable length and width (mm):

Length (L) = 300–2000 (in increments of 100)
Width (B) = 300–1000 (in increments of 100)

The dimensions refer to the grate size of the drain.

Variable top section depth (mm):

Top section depth (D)* = 70, 100, 150, or 200

70 mm is recommended when a low installation height is required.
150/200 mm is recommended for extra buffer volume or for lengths over 800 mm (to ensure sufficient slope towards the outlet).

*For floor types Tile K4 and K5, the depth measurements differ from those above. Read more under "Waterway, total height, upper part depth, and slope towards outlet".

Clinker floor K3

Floor material: Clinker in adhesives

Water proofing: Floor without waterproofing

Water proofing drain flange: None

Clinker floor K4

Floor material: Clinker directly on waterproofing layer

Water proofing: Waterproofing layer that can be rolled/spread and connected to a smooth stainless steel flange

Water proofing drain flange: 50 mm wide stainless adhesive flange

Clinker floor K5

Floor material: Clinker directly on waterproofing layer

Water proofing: Clinkers on sandwiched waterproofing membrane

Water proofing drain flange: Clamping flange

Resin flooring

Floor material: Resin flooring

Water proofing: Compound floor

Water proofing drain flange: Recess for resin floor

Vinyl flooring

Floor material: Vinyl flooring 1,5-4 mm

Water proofing: Vinyl flooring

Water proofing drain flange: FURO clamping flange

Vinyl flooring on wooden beams

Floor material: Vinyl flooring 1,5-4 mm

Water proofing: Vinyl flooring

Water proofing drain flange: FURO clamping flange

Concrete floor

Floor material: Concrete floor

Water proofing: Floor without waterproofing

Water proofing drain flange: None

Dimensions for floor drain FURO 113:

*The product has a slope towards the outlet.

For more information, see the section:
"Water flow, total height, upper part depth, and slope towards outlet"

Construction dimensions for floor drain FURO 113:

S₁ = B (Grate dimensions) + 310 mm
F₁ = B (Grate dimensions) + 250 mm

Drains and channels always feature a connection pipe and a designated flow path. The flow path is measured along the bottom line of the pipe.

To simplify product selection, we specify the total height (H) of our drains and channels. The total height measures the distance from the finished floor level down to the point where water exits the product. For bottom outlets, the measuring point begins at the start of the socket.

The total height (H) consists of the upper section depth (D) plus the outlet section of the product. Increasing the upper section depth also increases the total height, which in turn affects the flow path.

Dimensions for FURO 113:

The upper section depth (D) can be selected as 70, 100, 150, or 200 mm (100 mm is standard for sizes up to 600x400 mm).
For tile types K4 and K5, the upper section depth (D) varies between 50, 80, 130, and 180 mm (80 mm is standard for lengths up to 2000 mm).
The total height (H) of FURO 113 therefore varies between 202, 232, 282, and 332 mm (232 mm is standard for sizes up to 600x400 mm).
If an extension or inlet section is selected, the total height (H) increases by 82 mm.

Slope Towards Outlet:

The product’s slope towards the outlet depends on its length and selected upper section depth (D). For the standard configuration with a centrally located outlet, the following recommendations apply:

For use with cooking pots: An upper section depth of 150 or 200 mm is recommended. The bottom is step-folded, providing a slope towards the outlet of at least 7%.
For lengths between 1000–2000 mm and a recommended depth of 150 or 200 mm, the slope towards the outlet is at least 6%.

In cases where needs deviate from the above recommendations, the slope may be affected.

S 75

Side outlet Ø75 mm

Capacity 4 l/s

S 110

Side outlet Ø110 mm

Capacity 4,6 l/s

B 75

Bottom outlet Ø75 mm

Capacity 4,5 l/s

B 110

Bottom outlet Ø110 mm

Capacity 5,1 l/s

Trap

Part no. 220VH12

Trap with mechanical odor stop

Part no. 220VL12

Water trap, odor and backflow stop

Water trap with mechanical odor and backflow stop.

Part no. 220VLB12

Trap with shut-off function

Part no. 220VA2

Slip-resistant grid, L15

Slip-resistant grid with load class L15.

Maximum load: 1500 kg

Part no. Z-GALLER-L15

Strainer basket, 1,2 liters

Volume: 1.2 l
Capacity: 4.0 l/s

Part no. 220SK32

Strainer basket, 2.7 liters

The strainer basket is suitable for drains without a trap and drains with an extension part.

Volume: 2.7 l
Capacity: 4.0 l/s

Part no. 220SK41

Sand trap, 0.9 liters

Volume: 0.9 l
Capacity: 1.5 l/s

Part no. 220SF61

Sand trap, 1.5 liters

The sand trap fits in drains with an extension part or without trap.

Volume: 1.5 l
Capacity: 1.5 l/s

Part no. 220SF41

Lifting tool

Practical and ergonomic lifting hook for safe handling of grates and perforated plates. Provides a stable grip and reduces the risk of injury when lifting. Ideal for maintenance and installation.

Part no. 1LK1

Key for water trap

Key for locking Water trap 220VA2.

Part no. 1NV1

Extension part

Extension part, provides space for extra large accessories. Increases total height by 82 mm.

Part no. 1VPA220

Inlet part

Inlet part with Ø 50 mm connection. Increases total height by 82 mm.

Part no. 1VIN220

Radon sealing

Factory-installed radon and waterproofing.

Part no. 1VRT

Earth braid

Earth braid for potential equalization. Compatible with any attachment point on floor drains and channels.

For more information:
Installation instructions for earth braid

Part no. 1VJF

Drain without trap

Floor drain without built-in trap. A trap can be easily retrofitted if needed.

Capacity: 6 liters per second

Part no. 1VSU220

Mounting, threaded rod

Easy adjustment from above.

Height 300 mm.
Foot diameter = 100 mm.

Part no. 1SB30

Plastic mounting rod

Mounting rod that allows for easy adjustment from above.

Height: 300 mm
Foot diameter: 100 mm.

Use together with Installation accessories "Bits for plastic mounting rod".

Part no. 1SB40

Bits for plastic mounting rod

For easy height adjustment of plastic mounting rod.

Part no. 1BITS16

Sealant Aqua Tät

Sealant Aqua Tät for plastic flooring. Used under the flooring when installing the clamping frame.

Part no. 1AQUAT40

It is possible to customize our products. Below we show four customizations of FURO 113. Would you like help customizing your floor drain? Contact us.

Eccentric outlet

If our standard with center-aligned outlet does not work in the desired joist/structure, it is possible to customize the outlet placement.
Specify c/c from the left, min. 150 mm.

Smaller outlet part

When the joist limits the diameter of the hole, it is possible to switch to a smaller outlet part.

Dry strainer basket

If the strainer basket in the drain's outlet part is not sufficient, it is possible to cover the drain internally with strainer baskets. 1-3 units depending on the size of the drain.
The customization is available for the following floor types:

Screed floors
Tiled K3
Steel-ground concrete floors

Custom-shaped drain

For cooking pots and other machines where a large buffer volume and multiple outlets are desired, it is possible to customize the shape of the drain.
The customization is available for the following floor types:

Screed floors
Tiled K3
Steel-ground concrete floors

Documents

Technical overview (in swedish)

Type approval fire EI60 FURO 113

Installation instructions for earth braid

Do you need BIM or CAD files for your project? Download the files you need by clicking the links below.

Download MagiCAD model for this product.