Sand trap channel, width 150 mm FURO 149

Robust and durable sand trap channel in stainless steel, equipped with a removable sand trap box. The floor channel is ideal for industrial environments, workshops, and other demanding applications where efficient particle separation is essential. Available for multiple load classes and floor types.

Available in lengths from 600–20000 mm (in 100 mm increments) x width 150 mm.
The floor channel is equipped with a removable sand trap box with a capacity of 2.0 liters. The sand trap operates based on the sedimentation principle, meaning that heavier particles settle at the bottom at low flow rates. At higher flow rates, lighter materials may pass through into the drainage system.
Manufactured in stainless steel grade EN 1.4301 (SS 2333) or acid-resistant stainless steel grade EN 1.4404 (SS 2348).
Designed for embedding in concrete floors.
Compatible with various common floor types and features a 360° rotatable and angle-adjustable outlet.
The outlet section is positioned at the channel end.
Removable water trap with a handle for easy cleaning and maintenance.
EPDM rubber seals in compliance with EN 681-1, type Wc.
Stainless steel grating, divided into sections with a maximum weight of 8 kg per section.

Installation:

Delivered with protective cover to prevent concrete from entering the channel during installation.
Equipped with sturdy mounting brackets for secure anchoring in the floor slab.
For resin or epoxy floors, recess strips are included on the adhesion flanges.
Adjustable leveling feet allow for easy height adjustment from above (see installation accessories).

Technical Specification

Material: Stainless steel EN 1.4301 (SS 2333) or acid-resistant stainless steel EN 1.4404 (SS 2348)
Dimensions (mm):

Length: 600–20000 (in 100 mm increments)
Width: 150

Sand Trap: Removable sand trap box, 2.0-liter capacity, operating on the sedimentation principle
Water Trap: Removable, with handle for easy cleaning
Rubber Seals: EPDM in compliance with EN 681-1, type Wc
Grating: Grating or slotted cover

L15 For areas with light weight traffic. Tested acc. to EN 1253-1 with 10 kN load.
R50 For areas with medium weight traffic. Tested acc. to EN 1253-1 with 33 kN load.
M125 For areas with truck traffic. Tested acc. to EN 1253-1 with 85 kN load.

Variants

Variable length (mm):

Length (L) = 600–20000 mm (in increments of 100)
Fixed width: 150 mm

The dimensions refer to the channel's grating dimensions.

Variable Top Depth (mm):

Top Depth (D)* = 192, 232, or 312

192 is recommended for lengths up to 2000 mm, 232 is recommended for lengths between 2000–6000 mm and 312 is recommended for lengths between 6000–20000 mm. The channel depth (RD) then changes between 80, 120, and 200 mm.

Outlet Placement:
The standard is a gable-mounted outlet, 150 mm from the left gable, but alternative placements are available.

Please specify the c/c measurement from the left.

Clinker floor K3

Floor material: Clinker in adhesives

Water proofing: Floor without waterproofing

Water proofing drain flange: None

Resin flooring

Floor material: Resin flooring

Water proofing: Compound floor

Water proofing drain flange: Recess for resin floor

Concrete floor

Floor material: Concrete floor

Water proofing: Floor without waterproofing

Water proofing drain flange: None

Dimensions for FURO 149 floor channel:

*The product has a slope towards the outlet.

For more information, see the section:
"Water flow, total height, upper part depth, and slope towards the outlet"

Construction dimensions for FURO 149 sand trap channel:

S_{1 =} 425 mm

F_{1 =} 365 mm

Drains and channels always have a connection pipe and their water flow (V.g.) to consider. Water flow is always measured from the so-called bottom line of the pipe.

To facilitate product selection, we specify the total height (H) of our drains and channels. The total height is the distance from the finished floor surface to where the water exits the product. For bottom outlets, the measurement point is where the spigot begins.

The total height (H) is always made up of the top depth (D) plus the outlet section of the product. If the top depth is increased, the total height will also increase, affecting the product's water flow.

Dimensions for FURO 149:

Upper part depth (D) can be switched between 192, 232, and 312 mm (232 mm is a good choice for lengths between 2000–6000 mm). The channel depth (RD) then changes between 80, 120, and 200 mm.
Total height (H) for FURO 149 thus varies between 309, 349, and 429 mm (349 mm is a good choice for lengths between 2000–6000 mm).
If an extension part or inlet part is selected, the total height (H) increases by 60 mm.

Slope towards the outlet:
The product's slope towards the outlet varies depending on length and chosen upper part depth. With the standard configuration and end-positioned outlet, the following applies:

• For lengths up to 2000 mm and recommended depth of 192 mm, the slope towards the outlet is at least 1 %.
• For lengths between 2000–6000 mm and recommended depth of 232 mm, the slope towards the outlet is at least 1 %.
• For lengths between 6000–20000 mm and recommended depth of 312 mm, the slope towards the outlet is at least 0.7 %.

For needs other than the above recommendations, the slope is affected.

S 75

Side outlet Ø75 mm

Capacity 2,2 l/s

B 75

Bottom outlet Ø75 mm

Capacity 2,7 l/s

B 110

Bottom outlet Ø110 mm

Capacity 2,2 l/s

Trap

Trap included as standard.
Can be retrofitted.

Part no. 126VH2

Trap with odor seal

Trap with mechanical odor seal.

Part no. 126VL12

Closable trap

A trap that can be shut off with a key. When choosing accessories, an extension part is required.

Part no. 126VA2

Slip-resistant grid, L15

Slip-resistant grid with load class L15.

Maximum load: 1500 kg

Part no. Z-GALLER-L15

Grid, R50

Grid with load class R50.

Maximum load: 5000 kg

Part no. Z-GALLER-R50

Grid, M125

Grid with load class M125

Maximum load: 12500 kg

Part no. Z-GALLER-M125

Grate, M125

Grate with load class M125.

Maximum load: 12500 kg

Part no. Z-SPALTLOCK-M125

Sand trap, 2,0 liters

Sand trap included as standard.

Volume: 2.0 liters.

Part no. 126SF31

Strainer basket, 2,6 liters

Large strainer basket in stainless steel designed to effectively capture larger particles and debris that may flow with the water in the drainage system.

Volume: 2.6 l

Part no. 126SK31

Lifting tool

Practical and ergonomic lifting hook for safe handling of grates and perforated plates. Provides a stable grip and reduces the risk of injury when lifting. Ideal for maintenance and installation.

Part no. 1LK1

Key for water trap

Key for locking Vater trap 126VA2.

Part no. 1NV2

Extension part

Provides space for extra-large accessories.
Increases the total height by 60 mm.

Part no. 1VPA126

Inlet part

Inlet part with connection Ø 50 mm.
Increases the total height by 60 mm.

Part no. 1VIN126

Radon sealing

Factory-installed radon and waterproofing.

Part no. 1VRT

Earth braid

Earth braid for potential equalization. Compatible with any attachment point on floor drains and channels.

For more information:
Installation instructions for earth braid

Part no. 1VJF

Without trap

Floor drain without a trap. The trap can be retrofitted.

Capacity: 4 liters/second.

Part no. 1VSU126

Mounting, threaded rod

Easy adjustment from above.

Height 300 mm.
Foot diameter = 100 mm.

Part no. 1SB30

Plastic mounting rod

Mounting rod that allows for easy adjustment from above.

Height: 300 mm
Foot diameter: 100 mm.

Use together with Installation accessories "Bits for plastic mounting rod".

Part no. 1SB40

Bits for plastic mounting rod

For easy height adjustment of plastic mounting rod.

Part no. 1BITS16

Documents

Technical overview (in swedish)

Installation instructions for earth braid