Floor drain FURO 325

Floor drain FURO 325

För tömning av smutsvatten och avskiljning av sand från skurmaskiner.
410343ed-264b-4180-9b04-62ff0f3e54f0.png

Immediate delivery

  • Städrumsbrunnen är avsedd att gjutas in i golvet i städrummet för tömning av skurmaskinens smutsvatten.
  • Stor ackumulerande vattenvolym för att klara tömning av skurmaskinens smutsvattentank utan översvämning i städrummet.
  • Stor upplyftbar sandfångslåda med 7 L volym som avskiljer sand och annat skräp som kan sätta igen avloppssystemet.
  • Över sandfångslådan finns en turbulensreglerande styrplåt som reglerar vattenflödet till en jämn ström vilket gör att mer sand blir kvar i sandfångslådan.
  • Tömningsplåt, 200 mm bred spaltplåt med hål Ø 60 mm för enkel anslutning av tömnngsslang från städmaskin.
  • Valfri längd x bredd 400 mm.
  • För lagerlagda storlekar se dokument Omgående leverans.
  • Kvalitet syrafast rostfritt EN 1.4404 (SS 2348).
  • För ingjutning i betonggolv.
  • Överdelar för klinkergolv, massagolv, plastmatta samt stålslipat betonggolv som är vridbara 360°, vinkelställbara och teleskopiska.
  • Gavelplacerad utloppsdel med urtagbart vattenlås.
  • EPDM-gummitätningar enligt EN 681-1 typ Wc.
  • Rostfritt, halkskyddat rutgaller, utfört i delar med max vikt 6 kg.
  • Installationstillbehör som ingår: Levereras täckt för att hindra betong från att rinna ner i brunnen under gjutning. Rejäla fästöron för förankring i bjälklaget. Dessa ger möjlighet till enkel höjdjustering ovanifrån. Vid massagolv ingår ursparingslister på vidhäftningsflänsar.
  • L15 For areas with light weight traffic. Tested acc. to EN 1253-1 with 10 kN load.
  • M125 For areas with truck traffic. Tested acc. to EN 1253-1 with 85 kN load.
  • För skurmaskiner av typen ”Gå-bakom” och för små åkbara med smutsvattentankar mellan 15-120 liter rekommenderas storlek 600x400 mm.
  • För större skurmaskiner med smutsvattentank mellan 120-150 liter bör brunnen vara minst dimension 800x400 mm för att få tillräckligt stor ackumulerande volym.
  • För mycket stora maskiner bör städrumsbrunnen dimensioneras individuellt.

Variants

FURO325_VA_1.jpg
FURO149_VA_2.jpg

Depth measurements (mm):

Upper part depth (D) = 210
Channel depth (RD) = 95

Clinker floor K3

Clinker floor K3

Floor material: Clinker in adhesives
Water proofing: Floor without waterproofing
Water proofing drain flange: None
Clinker floor K4

Clinker floor K4

Floor material: Clinker directly on waterproofing layer
Water proofing: Waterproofing layer that can be rolled/spread and connected to a smooth stainless steel flange
Water proofing drain flange: 50 mm wide stainless adhesive flange
Clinker floor K5

Clinker floor K5

Floor material: Clinker directly on waterproofing layer
Water proofing: Clinkers on sandwiched waterproofing membrane
Water proofing drain flange: Clamping flange
Resin flooring

Resin flooring

Floor material: Resin flooring
Water proofing: Compound floor
Water proofing drain flange: Recess for resin floor
Vinyl flooring

Vinyl flooring

Floor material: Vinyl flooring 1,5-4 mm
Water proofing: Vinyl flooring
Water proofing drain flange: FURO clamping flange
Concrete floor

Concrete floor

Floor material: Concrete floor
Water proofing: Floor without waterproofing
Water proofing drain flange: None
FURO325_BMATT_1.png

Dimensions for FURO 325 cleaning room drain:

*The product has a slope towards the outlet.

For more information, see the section:
"Water flow, total height, upper part depth, and slope towards outlet"

Byggmått_större brunn_BMATT_1.jpg

Construction dimensions for FURO 325 cleaning room drain:

S1 = 710 mm
F1 = 650 mm

Drains and channels always have a connection pipe and their water flow (V.g.) to consider. Water flow is always measured from the so-called bottom line of the pipe.


To facilitate product selection, we specify the total height (H) of our drains and channels. The total height is the distance from the finished floor surface to where the water exits the product. For bottom outlets, the measurement point is where the spigot begins.


The total height (H) is always made up of the top depth (D) plus the outlet section of the product. If the top depth is increased, the total height will also increase, affecting the product's water flow.

Dimensions for FURO 325:

  • Upper part depth (D) is 210 mm. The channel depth (RD) is 95 mm.
  • Total height (H) is therefore 342 mm.


Slope towards the outlet is adapted to the product and floor type.

 

220S75_utlopp.png
S 75

Side outlet Ø75 mm

Capacity 4 l/s

220S110_utlopp.png
S 110

Side outlet Ø110 mm

Capacity 4 l/s

220B75_utlopp.png
B 75

Bottom outlet Ø75 mm

Capacity 4 l/s

220B110_utlopp.png
B 110

Bottom outlet Ø110 mm

Capacity 4 l/s
 

Trap

Trap

Part no. 220VH12

Trap with mechanical odor stop

Trap with mechanical odor stop

Part no. 220VL12

Water trap, odor and backflow stop

Water trap, odor and backflow stop

Water trap with mechanical odor and backflow stop.

Part no. 220VLB12

Trap with shut-off function

Trap with shut-off function

Part no. 220VA2

Slip-resistant grid, L15

Slip-resistant grid, L15

Slip-resistant grid with load class L15.

  • Maximum load: 1500 kg

Part no. Z-GALLER-L15

Grid, M125

Grid, M125

Grid with load class M125

  • Maximum load: 12500 kg

Part no. Z-GALLER-M125

Strainer basket, 1,2 liters

Strainer basket, 1,2 liters

  • Volume: 1.2 l
  • Capacity: 4.0 l/s

Part no. 220SK32

Lifting tool

Lifting tool

Practical and ergonomic lifting hook for safe handling of grates and perforated plates. Provides a stable grip and reduces the risk of injury when lifting. Ideal for maintenance and installation.

Part no. 1LK1

Key for water trap

Key for water trap

Key for locking Water trap 220VA2.

Part no. 1NV1

Radon sealing

Radon sealing

Factory-installed radon and waterproofing.

Part no. 1VRT

Earth braid

Earth braid

Earth braid for potential equalization. Compatible with any attachment point on floor drains and channels.

For more information:
Installation instructions for earth braid

Part no. 1VJF

Drain without trap

Drain without trap

Floor drain without built-in trap. A trap can be easily retrofitted if needed.

  • Capacity: 6 liters per second

Part no. 1VSU220

Mounting, threaded rod

Mounting, threaded rod

Easy adjustment from above.

  • Height 300 mm.
  • Foot diameter = 100 mm.

Part no. 1SB30

Plastic mounting rod

Plastic mounting rod

Mounting rod that allows for easy adjustment from above.

  • Height: 300 mm
  • Foot diameter: 100 mm.

Use together with Installation accessories "Bits for plastic mounting rod".

Part no. 1SB40

Bits for plastic mounting rod

Bits for plastic mounting rod

For easy height adjustment of plastic mounting rod.

Part no. 1BITS16

Sealant Aqua Tät

Sealant Aqua Tät

Sealant Aqua Tät for plastic flooring. Used under the flooring when installing the clamping frame.

Part no. 1AQUAT40

SH.png BVB.svg
MagiCAD Cloud

BIM and CAD files

Do you need BIM or CAD files for your project? Download the files you need by clicking the links below.

Magicad Cloud

Download MagiCAD model for this product.

MagiCAD Selection tool

Download MagiCAD model for this product.

Do you have any questions?

Do you have questions and concerns about production or do you need help with planning?

Common questions Contact us